Aletha & Miss Jane are looking forward
to snuggling down for a good nights sleep in their
new bed. It's a comfy spot for reading too.
The mattress has been tufted & the
bedding is finished.
When I was a young girl & spent time at my Grandad's
cabin, I slept in the screened porch on an old iron bed
that had a feather mattress & one large feather
bolster pillow. I have to say, the best sleepin' ever, is bein'
on your Grandad's porch, swallowed up by a feather mattress,
with a cool summer night's breeze blowing & not a care
in the world!
I stitched some simple warm flannel sheets
& pillow cases.
My "first" quilt fits well enough for now.
Aletha & Miss Jane love the little English cottages,
it reminds them of their favorite author's home, Hill Top.
Learn more about Beatrix Potter's life here:
Peter Rabbit
Making the mattress was really very simple.
To get the appropriate size for the top and bottom pieces,
I measured the length and width of the interior of
the bed. I added a seam allowance on both sides and
both ends for the final measurement. I cut 2 pieces,
the top and bottom of the mattress.
I measured all around the top piece and doubled
that to get the length needed for the piping. I added
a few inches for overlapping the ends together.
I cut a long strip of fabric for the piping. I actually
had to stitch a couple pieces together to get the
length needed. I basted the cording inside the strip.
(Use cording appropriate for the size of mattress).
To make the "side" panel of the mattress, I decided how
tall I wanted it to be, then added a seam allowance to the top
and bottom. I then cut enough strips to go all around the
top panel adding a seam allowance at the ends.
I had to stitch together a couple pieces to have
enough. I matched the stripes.
I marked my stitching lines on the top
& bottom pieces of the mattress. I cut out a
small cardboard template to mark my
curved corners. Much easier than
a square corner.
I pinned, then basted piping to the right
side of the mattress top. Be sure to attach the
piping right next to the drawn stitching line.
Large basting stitches that don't need to be
neat and pretty.
This is how I butted the ends of the piping
strips together.
Fold the end of the bottom section toward the inside
about 1/4 inch. Lay the other end on top, butt the
cording together, fold over and pin.
I couldn't exactly match the fabric pattern,
but I got close.
I clipped all curves throughout the entire process.
Piping basted to the top.
Next step, I pinned then basted the side panel to the top.
Right sides together.
Then I pinned and basted piping to the bottom
of the side. Right sides together.
Top and sides with all piping basted.
I pinned then basted the bottom of the mattress to the
bottom of the side panel, leaving a large opening
for stuffing. Again, with right sides together.
I stitched the seams with off white button hole thread
in a back stitch. Then removed all the basting stitches.
Ticking is a heavier fabric, regular thread just
didn't seem strong enough.
I nearly stole my hubby's feather pillow for the
stuffing, but I thought he might not appreciate the
importance of feathers in the dolly's mattress, so
I used polyester stuffing. I turned it right side
out and I stuffed it
full, then closed the opening
with a ladder stitch.
How To Sew A Ladder Stitch
This is the placement of the buttons I
used for tufting the mattress.
I marked the top and bottom panels with X's.
I covered 8
shank buttons for the top and
chose 8 smaller red
shank buttons for the
bottom of the mattress.
Covering small buttons with heavier ticking
fabric was a chore, I gave up after 8!!!!
I used a long length of button hole thread
doubled
to tie the top & bottom buttons together. I used
a very long upholstery needle with a
big eye.
I started by inserting my needle into the bottom X.
Coming out in the corresponding X on the
top of the mattress. (Don't pull the thread
all the way through)
I threaded the button, re inserted the needle
next to the first thread, coming out in the X
on the bottom.
I threaded the bottom button.
(Slightly off, but it won't show!)
Then I pulled the 2 buttons closer together, to
get the tufting look.
I tied several knots under the bottom button.
Then re threaded all 4 lengths of thread onto
my needle, inserted the needle just underneath
the button and buried the thread ends inside
the mattress. I repeated this with all the
pairs of buttons.
This is the bottom of the mattress.
It's lump bumpy, but so was the
feather mattress I slept on as a child.
The covered buttons look really nice, so it
was worth all the aggravation.
I had hoped to sew this on the machine, but my
piping foot wasn't big enough for the size cording I chose,
even by hand it wasn't difficult.
My mother once told me that sewing was lots & lots of
planning, measuring, cutting, fitting, pinning, & basting,
with a little bit of sewing thrown in at the end.
Oh, so true!
Happy Sewing
